Go Power uses MC4 connectors like part # 34279532 for their solar panel connections. You would not be able to mix your two panels together and run them through the Go Power Solar Controller. You would need to use additional Go Power branded panels like the # 34282181 to add on to your solar power system.
The Acopower panel can still be ran to your battery separately though if that's what you're wanting to do. You would just need to drill a new hole in the run and run the wire from the... view full answer...
Though you will not need to make any alterations to the axle to up your bolt pattern to a 5 on 4-1/2, but you will need to verify your bearings to make sure the new hubs will fit properly. Form what I could find, your 2018 Forest River Flagstaff E-Pro E14FK has a GVWR of 2,917 pounds. This means you most likely have a 3,500 pound Dexter axle.
The typical Dexter axle of this capacity will use the # L68149 inner bearing and # L44649 outer bearing. Again, you will need to verify these bearings,... view full answer...
The Curt Ball Mount for 2" Hitches part # C84WR has an 8,000 lb weight capacity which is for both rise and drop positions. In regards to fit, this will vary by receiver, some are tighter than others and some are looser. It comes down to both the hitch side and ball mount side. That said, if you're worried about rattle you can add an anti-rattle like the Curt Anti-Rattle Hitch Clamp for 2" Hitches part # C27UR. view full answer...
The correct slide topper awnings for a 2020 Forest River Flagstaff E-Pro with a 154" wide slide and 83" wide slides are as follows:
154" Wide Slide: Solera RV Slide-Out Awning part # LCV000168109 for Black or part # LCV000163300 for White
83" Wide Slide: Solera RV Slide-Out Awning part # LCV000165062 for Black or part # LCV000163287 for White
Please note, slide-outs need to be measured from the outside of each slide. view full answer...
Yes, the TorkLift PowerArmor Locking Battery Box # TLA7708R will be able to handle both of your batteries as there is 26-1/2" of total length inside, as well as 7-5/8" off width clearance (see attached). view full answer...
Adding the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # DT78MR is a great option for a hitch on your 2020 Jeep Wrangler Unlimited. It is going to have the highest weigh capacity. The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 6,000 lbs GTW, 600 lbs TW Item # EQ37060ET is going to work great with the draw-tite hitch. The 600lb/6000lb weight capacities on the weight distribution are going to be the maximum weight. With the draw-tite... view full answer...
The length I'm seeing for your 2019 Forest River Flagstaff E-Pro E19FD is 20' so you'll likely be around 17' in body length and would need the ADCO # AD37ZR since it fits 15' - 18' lengths. If you measure the body and are at or above 18' then you'll want to size up to the # AD97ZR, which fits 18' - 20' lengths. view full answer...
Lift kits aren't specific to any trailer, they are specific to axles, and based on my research it looks like your 2019 Flagstaff E-Pro uses torsion axles. I wasn't able to determine what axles they were specifically but your trailer has a GVWR of just under 4,000 lbs.
With that in mind, there are three potential options depending on your specific axle. If you have a #10 Torflex axle with a 2,300 to 4,000 lb capacity you can use Torflex Lift Kit # K71-707-01.
If you have a Lippert 3,500... view full answer...
The Adco Olefin HD RV Cover # AD37ZR fits trailers 15' 1" to 18' in length so it should be enough for an 182" length. If you instead meant 18' 2" in length then yes, you would want to size up to part # AD97ZR. view full answer...
It looks like the overall length of the 2022 Flag Staff E PRO Model 19FD is 20' 8" including the tongue but covers aren't supposed to fit over the tongue. The Adco Olefin HD All-Climate + Wind RV Cover # AD97ZR you're looking at is for travel trailers 18'1" - 20' long. Since the tongue of a trailer is somewhere around 3' long you might need to use the next size down which is part # AD37ZR and fits travel trailers 15'1" - 18' long.
Your dealer should be able to measure out just the box... view full answer...
Go To Results